Home > News > Content
What Need To Do Before Use The Cultivators And Tiller
- Sep 25, 2017 -

Preparation prior to operation


    Check the engine oil level will be placed on the position of the engine, remove the oil foot and wipe the oil film, and then into the oil dipstick hole, then remove the oil foot to observe the oil level, gasoline engine oil to the oil hole neck, diesel oil should be to the middle part of the oil foot, gasoline engine and diesel engine can not be exchanged or mixed use if the gasoline engine, diesel oil, gasoline engine will make the cremation plug serious carbon deposit and wouldn't start, if the gasoline engine diesel engine, diesel engine connecting rod tile will make the moving parts such as rapid wear, which caused the engine damage. Most users do not see the right to check the oil dipstick, easy mistake is the oil foot from the machine after the removal of no clean look, this watch is mistaken for the oil a lot, and sometimes even have no oil, it will cause damage to the engine burning tile. The new machine first add enough oil, machine running hours should be put out of oil, then add new oil to residual impurities and machine wear down the metal powder inside the machine wash machine, wear-resistant, durable, while the machine is hot put old oil, so the oil and impurities is a mixed state, and the concentration is low, easy to be put in the net impurity. Check oil transmission box will be placed in the micro farming machine on the ground level, remove the transmission oil hole plug, the oil level should be in the lower edge of the oil hole, if the oil level is below the lower edge of the oil hole, add gear oil clean, if the transmission box has no oil or oil shortage, the gear box gear and bearing could damage in a few minutes. Check the fuel tank fuel, if the fuel shortage, should be made up of fuel, more than the number of gasoline engine gasoline, diesel engine with universal light diesel oil, the temperature at 10 degrees Celsius below 0 light diesel oil. When refuelling, no smoking or any Mars is detected. The water level in the tank (a water-cooled diesel engine) adds clean water to the tank until the float rises to the top. Adjust the clutch cable in the grip or release the handle (lever type: the lever pull back when the clutch), tillage machine (out) could not walk in, hold the handle when (lever type: the lever forwards), because the tension spring pull tension wheel up the triangle belt tension (called combination), tillage machine (with) walking machine (out) in the work of the state. If no clear separation of the clutch or the belt slipping, it is necessary to adjust the clutch cable bolt, the method is: lock nut loosen clutch cable pipe, wrench adjustment bolt, if no clear separation of the clutch, the adjustment bolt to internal rotation, until the clutch can separate and clear. If the clutch is not good (belt slipping), should the adjustment bolt to external rotation, until the clutch can be combined (belt slipping), then the lock nut and bolt to adjust if the clutch cable can make the clutch work, you need to adjust the belt tension to the hand on the throttle handle to the maximum position when the engine throttle should also be opened to the maximum position, if the throttle handle on the arm to the maximum position of the engine throttle can not be opened to the maximum position, it is necessary to adjust the throttle cable, the method is: first loosen the lock nut gasanchor, adjust screw rotation, to meet the above requirements to lock nut.


Adjustment of tightness of V-belt


    The triangle belt is on the lower belt by hand gently hold appropriate, too loose or too tight to adjust, loosen a method is: engine mounting bolts, if gasoline engine, in addition to loosen the mounting bolts, should also loosen the connecting plate of engine and transmission box fixing bolt, forward or backward the appropriate mobile engine, the triangle belt tightness meet the above requirements, the corresponding bolt tightening. Adjust the height to the hand frame operator feel the appropriate level as the standard, the engine is generally in a horizontal position, with a high waist arm high appropriate adjustment method is to adjust the bolts to remove the handrail, handrail height change operation, and then adjust the bolt into the hole and the corresponding adjustment nut. Depth adjustment rod pin out resistance, resistance to change on the connecting rod hole, can adjust the tillage depth, penetration resistance above the hole pin rod, rod resistance decreased, tillage depth increases, the penetration of pin hole, the resistance bar rises, tillage depth decreases. Some machines use bolts to adjust the height of the resistance bar. When adjusting, loosen the bolt first, adjust the resistance bar to the required position, and then tighten the bolt. Select the matching machine, according to the soil conditions, select the appropriate equipment of winter paddy field tillage paddy wheel selection, selection of dry farming rotary blade (if in the weeds and deep, should choose the type, mowing machine) dryland paddy field, the first time with a rotary blade or composite knife, second times with paddy wheel, junction tillage machine and micro cultivator power output shaft must be safe and reliable (wear pin and elastic pin). In the installation, pay special attention to the difference between the left and right, must not install anti.